Intended for use with selected oscilloscope product lines only. In all supported product lines, it contains the capabilities included in CANbus TD and LINbus TD, and some oscilloscope product lines also support FlexRaybus TD as well.
Intended for use with selected oscilloscope product lines only. In all supported product lines, it contains the capabilities included in CANbus TD and LINbus TD, and some oscilloscope product lines also support FlexRaybus TD as well.
Depending on the time base or the amount of zoom, the decode information is condensed or expanded to better assist in understanding events during short or long acquisitions.
Features
Conditional DATA trigger setup ("T")
The trigger permits a conditional (<, ≤, =, >, ≥, <>, inside a range, outside a range) setup for the DATA condition. This is especially useful in situations where abnormal events should be monitored, such as when a CAN node broadcasts a low or high engine RPM or coolant pressure.
Trigger flexibly across data bytes ("T")
CAN remains the most used vehicle serial data bus. Many vehicle bus software architectures are very message dense, and data for a single message is spread across multiple data bytes. The hexadecimal and measurement toolsets permit isolation of specific bit-level data patterns in one or more data bytes, e.g., data location in bits 17 to 28 in data bytes 3, 4, and 5. This provides significant advantages in isolating the exact information or behaviour you need. Symbolic message/signal setup is even simpler.
Intuitive, colour-coded decode overlays ("D")
A transparent overlay with colour-coding for specific portions of each protocol and the entire message frame makes it easy to understand your serial data information. Unlike other solutions, with protocol decode information away from the signal, our solution correlates the waveform and the protocol decode directly on the display. As the acquisition length is expanded or shortened, the decode overlay will adjust to show you just the right amount of information.
Interactive table summarizes results ("D")
Turn the oscilloscope into a protocol analyzer with a tabular display of decoded information. Customize the table to show only the data of interest and touch a message in the table to automatically zoom to it and display it on the screen. Export the table for offline analysis. Up to four different decoded signals of any type may be simultaneously displayed in the table.
Powerful conditional Data triggering
Completely isolate specific protocol message events for better understanding and debug. Use a conditional DATA trigger to select a range of DATA to select a range of DATA values to trigger on, not just a single DATA value.
Convenient table display summarizes results
Turn your oscilloscope into a protocol analyzer with the table display of protocol information. Custom configure the table to display the information you want, and export table data into an Excel file. Touch the message in the table and automatically zoom for detail. In all cases, the table never obscures your waveform.
Search and zoom
The powerful search engine can quickly find an Event, Packet, Transaction, or Protocol Error. Search through a long record of decoded data by entering any of the available search criteria by entering a value or simply finding the next occurrence.
Probes | |
Standard | One PP017 (0.2" or 5 mm) per channel or one PP018 (0.2" or 5mm) per channel |
Probing System | BNC and Teledyne LeCroy ProBus for Active voltage, current and differential probes |
Display System | |
Size | 12.1" (30.7 cm) wide TFT-LCD touch-screen |
Resolution | 1280 x 800 |
Connectivity | |
Ethernet Port | 2 x 10/100/1000Base-T Ethernet interface (RJ-45 connector) |
USB Host Ports | 6 x USB ports total (2 x front USB ports) |
USB Device Port | 1 x USBTMC |
GPIB Port (Optional) | Supports IEEE – 488.2 |
External Monitor Port | Standard 15-pin D-Type SVGA-compatible DB-15 connector, DVI connector and HDMI connector |
Remote Control | Via Windows Automation, or via Teledyne LeCroy remote command set |
Processor/CPU | |
Type | Intel B810 Celeron processor 1.6 GHz or better |
Processor Memory | 4 GB Standard |
Operating System | Windows Embedded Standard 7, 64-Bit |
Power Requirements | |
Voltage | 100 to 240 V AC + 10% at 45 to 440 Hz (automatic AC voltage selection) |
Power Consumption (Nominal) | 200 W / 200 VA |
Max Power Consumption | 320 W / 320 VA (with all PC peripherals and active probes connected to 4 channels) |
Environmental | |
Temperature | Operating: 41 to 104°F (5 to 40°C) Non-operating: -4 to 140°F (-20 to 60°C) |
Humidity | Operating: 5 to 90% relative humidity (non-condensing) up to 87.8°F (31°C) Upper limit derates to 50% relative humidity (noncondensing) at 104°F (40 °C) Non-operating: 5 to 95% relative humidity (non-condensing) As tested per MIL-PRF-28800F |
Altitude | Operating: 10,000' (3,048 m) maximum at ≤30°C Non-operating: Up to 40,000' (12,192 m) |
Regulatory | |
CE Certification | Low Voltage Directive 2006/95/EC EN 61010-1:2010, EN 61010-2-030:2010 EMC Directive 2004/108/EC EN 61326-1:2006, EN61326-2-1:2006 |
UL and cUL Listing | UL 61010-1 (3rd Edition) UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No.61010-1-12 |
Physical | |
Dimensions (HWD) | 11.48 x 15.72 x 5.17" (291.7 x 399.4 x 131.31 mm) |
Weight | 12.9 lbs (5.86 kg) |
Probes | |
Standard | One PP017 (0.2" or 5 mm) per channel or one PP018 (0.2" or 5mm) per channel |
Probing System | BNC and Teledyne LeCroy ProBus for Active voltage, current and differential probes |
Display System | |
Size | 12.1" (30.7 cm) wide TFT-LCD touch-screen |
Resolution | 1280 x 800 |
Connectivity | |
Ethernet Port | 2 x 10/100/1000Base-T Ethernet interface (RJ-45 connector) |
USB Host Ports | 6 x USB ports total (2 x front USB ports) |
USB Device Port | 1 x USBTMC |
GPIB Port (Optional) | Supports IEEE – 488.2 |
External Monitor Port | Standard 15-pin D-Type SVGA-compatible DB-15 connector, DVI connector and HDMI connector |
Remote Control | Via Windows Automation, or via Teledyne LeCroy remote command set |
Processor/CPU | |
Type | Intel B810 Celeron processor 1.6 GHz or better |
Processor Memory | 4 GB Standard |
Operating System | Windows Embedded Standard 7, 64-Bit |
Power Requirements | |
Voltage | 100 to 240 V AC + 10% at 45 to 440 Hz (automatic AC voltage selection) |
Power Consumption (Nominal) | 200 W / 200 VA |
Max Power Consumption | 320 W / 320 VA (with all PC peripherals and active probes connected to 4 channels) |
Environmental | |
Temperature | Operating: 41 to 104°F (5 to 40°C) Non-operating: -4 to 140°F (-20 to 60°C) |
Humidity | Operating: 5 to 90% relative humidity (non-condensing) up to 87.8°F (31°C) Upper limit derates to 50% relative humidity (noncondensing) at 104°F (40 °C) Non-operating: 5 to 95% relative humidity (non-condensing) As tested per MIL-PRF-28800F |
Altitude | Operating: 10,000' (3,048 m) maximum at ≤30°C Non-operating: Up to 40,000' (12,192 m) |
Regulatory | |
CE Certification | Low Voltage Directive 2006/95/EC EN 61010-1:2010, EN 61010-2-030:2010 EMC Directive 2004/108/EC EN 61326-1:2006, EN61326-2-1:2006 |
UL and cUL Listing | UL 61010-1 (3rd Edition) UL 61010-2-030 (1st Edition) CAN/CSA C22.2 No.61010-1-12 |
Physical | |
Dimensions (HWD) | 11.48 x 15.72 x 5.17" (291.7 x 399.4 x 131.31 mm) |
Weight | 12.9 lbs (5.86 kg) |