Designed for monitoring the performance of photovoltaic arrays, the A89DC-08 offers 8 individual current inputs via built-in Hall-effect CTs. Includes MODBUS-RTU communications
Designed for monitoring the performance of photovoltaic arrays, the A89DC-08 offers 8 individual current inputs via built-in Hall-effect CTs. Includes MODBUS-RTU communications
Discontinued!
This product has been discontinued and is no longer available. There are no replacement options.
We can help you find what you need:
Processor | Arm7 embedded CPU |
LED | Alive (green), RS485 TX, RX (yellow) |
Protocol | Modbus RTU |
Addressing | Modbuss address may be set from 1 to 247 via Modbus register. |
Power Supply | Power input 24vdc at 382mA (power supply not included) |
Inputs | 8 DC Hall Effect Sensors, non-contact. Maximum range +50Amps to -50Amps DC at 600V DC The Hall Effect sensor openings are intended to be used with Insulated wire. Cat I measurement device4 0.49 inch by 0.35 inch opening for load wire. |
Accuracy | ±1% of full scale (±0.5A) |
Measurements | DC current per channel, instantaneous and average Average DC current (of 8 channels), instantaneous and average |
Alarming | Low alarm may set a percent of DC average of other channels. Alarms may be disabled below a minimum average current level. Minimum time for alarm may be set to prevent alarms on brief events. Unused channels may be disabled to exclude them from total and average calculations. |
Communications | RS-485 (+, -, S), 9600 baud, N, 8, 1, two wire. Supports up to 32 external devices (expandable) |
Isolation | The RS485 terminals electrically isolated to 1500V from the remainder of the A89DC-08 board. |
Environmental | North America: Temperature 0 to 60°C, 0 to 95% humidity, non-condensing. Pollution Degree 2, Altitude up to 2000M. For indoor and outdoor use when used in an appropriate enclosure. The A89DC-08 must be mounted inside a NEMA rated electrical enclosure for safety and isolation requirements. |
Safety | UL61010 Recognized File: E320540 (Model A89DC-08) |
EMC | FCC CFR 47 Part 15, Class A |
Size | 10.25" x 2.5" x 1.75" (260mm x 64mm x 45mm) |
Mass | 0.83 lbs (0.375 kg) |
1 Outputs are intended for low voltage class 2 inputs.
2 If the product is used in a manner not specified by the manufacture, the protection provided by the equipment may be impaired.
3 May be dependent on forced air cooling. See chapter on temperature in this manual for details.
4 WARNING: Not for use within measurement categories II, III or VIPage.
Processor | Arm7 embedded CPU |
LED | Alive (green), RS485 TX, RX (yellow) |
Protocol | Modbus RTU |
Addressing | Modbuss address may be set from 1 to 247 via Modbus register. |
Power Supply | Power input 24vdc at 382mA (power supply not included) |
Inputs | 8 DC Hall Effect Sensors, non-contact. Maximum range +50Amps to -50Amps DC at 600V DC The Hall Effect sensor openings are intended to be used with Insulated wire. Cat I measurement device4 0.49 inch by 0.35 inch opening for load wire. |
Accuracy | ±1% of full scale (±0.5A) |
Measurements | DC current per channel, instantaneous and average Average DC current (of 8 channels), instantaneous and average |
Alarming | Low alarm may set a percent of DC average of other channels. Alarms may be disabled below a minimum average current level. Minimum time for alarm may be set to prevent alarms on brief events. Unused channels may be disabled to exclude them from total and average calculations. |
Communications | RS-485 (+, -, S), 9600 baud, N, 8, 1, two wire. Supports up to 32 external devices (expandable) |
Isolation | The RS485 terminals electrically isolated to 1500V from the remainder of the A89DC-08 board. |
Environmental | North America: Temperature 0 to 60°C, 0 to 95% humidity, non-condensing. Pollution Degree 2, Altitude up to 2000M. For indoor and outdoor use when used in an appropriate enclosure. The A89DC-08 must be mounted inside a NEMA rated electrical enclosure for safety and isolation requirements. |
Safety | UL61010 Recognized File: E320540 (Model A89DC-08) |
EMC | FCC CFR 47 Part 15, Class A |
Size | 10.25" x 2.5" x 1.75" (260mm x 64mm x 45mm) |
Mass | 0.83 lbs (0.375 kg) |
1 Outputs are intended for low voltage class 2 inputs.
2 If the product is used in a manner not specified by the manufacture, the protection provided by the equipment may be impaired.
3 May be dependent on forced air cooling. See chapter on temperature in this manual for details.
4 WARNING: Not for use within measurement categories II, III or VIPage.